CenterPoint meter pole specifications

AN HORING Meter poles over 75 feet from the ooperative pole must have an anchor assembly. Sometimes Jurisdictions will allow you to install what is called a spider box with extra receptacle outlets on it, but they also must meet NEC and jurisdictional codes. Learn more about hiring developers or posting ads with us

Start here for a quick overview of the site Basically, you build the pole to the utilities specifications, and follow NEC while you do it. The rest of your list should be covered by the utilities specification, and/or requirements of the builder.

By clicking “Post Your Answer”, you agree to our To subscribe to this RSS feed, copy and paste this URL into your RSS reader. or 6" Round Materials Required 100 AMP 4' 18" Min.

The panel you listed looked like what we use at RV sites for 240v 50 amp supplies. Home Improvement Stack Exchange works best with JavaScript enabled I generally will go with a 60A feeder.In conclusion what I am saying is that there are pre qualified types of power pole directions that cover all of the NEC requirements without having to go through the entire code to get it right, and is perfect for a DIY party to construct.

There are some questions about breakers that serve feeders other than standard power outlets being GFCI protected. As far how it is set up for underground we attach the panel to a 4x4 post, overhead depends on the length of the run and if it crosses a road for for example we will usually set a pole at 18' for the feed, if the drop will have nothing but foot traffic between the utility pole and the temp pole we will set it at 12'. The most important thing to remember about any temporary power set up is that all power must be GFCI protected.

The anchor assembly is to be a minimum of 20 feet from the base of the meter pole consisting of a 6 foot rod and a 6000# an-chor. When a pole taller than 30 feet is used, wire in conduit is recommended. Learn more about Stack Overflow the company gas meter will be Customer designed, owned, maintained and installed at Customer cost. The best answers are voted up and rise to the top It only takes a minute to sign up.The county requires the temporary power pole to be installed "in accordance with the NEC" but doesn't elaborate further.Are there any specific requirements for temp power poles in the NEC 2014 or 2017 editions, such as number of receptacles, in use weather proof covers, amperages, number of plugs, etc?There are some pre-built temporary power panels like Does anyone know the relevant code section(s) that lists specifically what features are required or not required for temp poles?In this state the power pole is regulated by the requirements on the utility company, but must be inspected and approved by the AHJ. If you take a good look at the image I posted. below).

How many code sections would you have to address just to build a temporary power and hope you got it right?

9.

Outages: 800.972.1093. Office: 903.935.7936. Make sure the meter base is located at the height the utility specifys or they may not energise the line ( my county the utility limits the meter to 6') so your panel will usually be below this for overhead. Basically, you build the pole to the utilities specifications, and follow NEC while you do it. A temporary box like you've linked to, should meet the NEC requirements for receptacle covers.Temporary services can supply 240v, we have 2 such buildings going up right now and both have 240 avaiable one is commercial and one is residential. "Very satisfied! These wired meter poles are complete with meter socket, mast, and 200-amp main breaker (or fuses for 600 volt rated disconnect poles).

The breaker box includes unused breaker positions suitable for connecting outdoor electrical equipment such as heat pumps and water pumps. Panola-Harrison Electric Cooperative. With regard to in-use covers, what are you expecting to see?That entire NEMA 3R raintite enclosure in your example is an "in-use" enclosure.

Poles − Specifications and Dimensions,” and American Wood Protection Association Standards T1-10 and U1-10, as modified or described in Engineering Material Specification 57, “Preservative Treated Wood Poles and Stubs for Overhead Lines.” B. While every effort has been made to assure the. Code/ AHJ get tough on spider boxes in our area but we do use them, the inspector usually checks every foot of the cord supplying the box so we use type W cord because it is so much tougher than standard hard service cord. The rest of your list should be covered by the utilities specification, and/or requirements of the builder. C. The special emphasis on the role of the ANSI 05.1 wood othertwo standards, ANSI 05.2 and 05.3, also address pole standard specifications. One permanent service meter base will be furnished by the Co-op and may be picked up by the customer during regular office hours, M-F, 8:00 AM to 5:00 PM. 480V Delta or 277/480V Wye, 200 Amp & Below Service, Self-Contained Metering with Meter Disconnect Figure 16.

Featured on Meta If the receptacles are exposed to weather, then you'll need in-use covers. Anybody can answer

There's no "Temporary power pole requirements" section in the NEC. If the receptacles are exposed to weather, then you'll need in-use covers. 410 E. Houston St. Marshall, TX 75670 Discussion of topics Panola-Harrison Electric Cooperative is an equal opportunity provider and employer.If you wish to file a Civil Rights program complaint of discrimination, complete the USDA Program Discrimination Complaint Form, found online at U.S. Department of Agriculture, Director, Office of Adjudication, 1400 Independence Avenue, S.W., Washington, D.C. 20250-9410, by fax (202) 690-7442 or by email to Like I said some jurisdiction say its ok and some make you remove and blank out the breaker.