how to remove psu cover

Adding more with to the metal cover in the back for wiring as it was a pain to fit just about every piece of wiring down the very narrow cover. You can also find his work at SemiAccurate.com and his musings on Twitter.PCWorld helps you navigate the PC ecosystem to find the products you want and the advice you need to get the job done.

© Cardboard is a great way to quickly prototype parts like a PSU cover which can be hard to visualize.

A PSU shroud would be an easy mod to do to for this case and would help clean things up.First, I put together a quick mockup using cardboard. Don’t underestimate the importance of your PC’s power source. Thomas Ryan Now you can finally pull your old power supply out of your case. If your power supply unit (PSU) includes a power switch accessible on the rear of your PC, flip it to the off position, and then remove the side panel of your case so you can access the PSU.

Now you’ve got a PC that’s ready to run for years to come without issue—or at least without PSU-related issues. Plug the 24-pin power connector into your motherboard first, then go for the 4 or 8-pin CPU power connector. Finally plug any required PCI-E power connectors into your graphics card, then double-check all of the plugs to make sure they are securely seated. However, some cases don’t include this or you may want to upgrade your existing case with one, so I will show you how to make one on your own!For this guide, we’re going to use a build in the Carbide Series SPEC-04 Tempered Glass case.

Most modern cases include a power supply cover or shroud that cleans up the internal look of your PC by hiding things such as your PSU cables and drive cages.

Copyright A good power supply serves as the cornerstone for a low-maintenance and highly reliable computer.

As you remove each cable, pull it out of the case to avoid tangling them with the other cables. If you’re interested in the process I used, I covered spray-painting parts in a previous Mounting the cover is very straightforward, I did not want any screws to be seen so I used 3M double-sided tape and mounted the cover to the PSU itself.This is how it ended up looking mounted, much cleaner don’t you think?When the entire project was finished I ended up with a pretty great result, what do you think? 2020 CORSAIR. Set these safely to the side.

I used a sheet bender for this.This is how the part ended up looking after the bend, however I did not want it to be raw aluminum……so I spray-painted it white. Doing so also helps ensure that all power cables are disconnected, and makes it easier to remove the PSU from the case when you’re done. As you can see in the image above, it’s a great budget case with an open internal layout with the PSU and cables visible. Read our All rights reserved. Keep in mind that there’s nothing wrong with buying a power supply that provides more power than you actually need, especially if there’s the possibility of further PC component upgrades in your future. Remove the three (3) screws securing the PSU to the rear of the chassis [5]. A 6+2 pin connector used to provide power to graphics cards and CPUs. You may find it helpful to photograph which power cables went to which components so that you can have a reference for plugging in the cables on your new power supply.

You will need to disconnect all of these cables before the power supply can be removed, or else they’ll snag and hold the PSU in the case. A number of different power connectors lead from the power supply and power the different components in your computer. Seal your computer’s case back, plug everything back in, and power your computer up. If you took photos of or labelled the cables on your old power supply, you can now use those as a reference for figuring out how to connect the cables of your new power supply. Start by unplugging from the wall all of the cables connected to your computer. Don’t forget to remove the four- or eight-pin CPU power connector located near the CPU socket on the motherboard,and the 24-pin power cable connected to the motherboard along its mid-line on the left side.

This means that two or three years after buying your computer, you may find yourself with a perfectly functional desktop that one day decides either not to power on or to emit a puff of black smoke. Thomas Ryan is a freelance technology writer and product photographer from Seattle.

If your power supply unit (PSU) includes a power switch accessible on the rear of your PC, flip it to the off position, and then remove the side panel of your case so you can access the PSU.

Buying a boxed, pre-built desktop is a great way to pick up a computer on the cheap. Leave a comment and stay tuned for more how-to mod blogs.

In most cases there are only four screws, but designs differ from vendor to vendor. Swing open the front panel door and disconnect the power cables from the motherboard [1 & 2]. You can use these two tools to understand how much wattage your new power supply will need to deliver and which features you’ll want—unless you’re upgrading to a new, more powerful graphics card that demands a new, more powerful PSU.