Twitter Share
Exhaust air duct is not connected or blocked.
If the P2 or FL error code is displaying on the air conditioner, remove the drain port cap and tilt the air conditioner to the back so the water runs out of the drain outlet.
Eventually this did not work and researching online led us to believe that either the indoor pipe sensor or indoor PCB was bad.
Air conditioning and heating are part of our everyday life. There is usually not enough water in the drain pan to cause the air conditioner to shut off.To drain the unit less frequently, turn the fan speed to If no water is draining out when the air conditioner is tilted to the back, the unit will require a repair service.
It don’t blow cool air anymoreI have the same FO code that won’t go away. I know this is indicating that the tank is full, however I have completly drained the unit.
All Rights Reserved
Connect the duct and make sure it can function properly.
In order to get the best possible experience from our website, please follow below instructions.If you're using Internet Explorer 9 or earlier, you will need to An error code on the display of the room air conditioner can usually be resolved by performing a few simple troubleshooting steps.
Mitsubishi Air Conditioner Operation Light Flashing. I tried leaving it …
P2 or FL Display Will Not Clear After Draining It would be unthinkable to do without the comfort that these appliances bring by controlling the indoor air quality of our environments and allow us to live better.
Overall, how satisfied were you with the usefulness of this information?1-1.
Check Point: Check If The Refrigerant Is Charged Too Much; Check If The Voltage Is Too Low, Power Wringis Too Thin Or Too Long Or Contact Badly; Check If The Outlet Is Blocked Or The Condensor Is Dirty; Check The Outdoor Motor Work Normally; Count Measure: Regulate The Quantity Of Refrigerant …
Decrease the set temperature. Not to blow out cold air at the beginning of heating operation, the air conditioner automatically adjusts the fan speed gradually from lower to the set speed.
Flashing of POWER lamp indicates abnormalities. This will allow the air conditioner to maintain better cooling and humidity control, while reducing the strain on the unit when the temperature is turned back down for more cooling.E5 Error code indicates that the water collection tank is full.
I have drained it, reset it, leveled it, and cleaned it. The main control board is programed to send out a P2 code to protect the compressor from overheating and becoming damaged.
Suggest Remedies: Make sure all the windows and doors are closed. EMAIL
My LG LP0910WNR Air Conditioner flashes P2. The Phone Number you entered will not be used for any other purpose.To Help improve your LG.com experience we would appreciate you completing our survey.JavaScript appears to be disabled in your browser.
Spent lots of time online trying to find these replacement parts to no avail. LG.com utilizes responsive design to provide a convenient experience that conforms to your devices screen size. 1.
The air conditioner is working properly.If the error code on your unit is not listed here, refer to your owner's manual to resolve the model specific error code.
What is it & how can I fix it? The fans should be able to spin easily with no debris blocking them. Clean the air filter. Please enable JavaScript to ensure you get the most out of the LG site, products, and services
Direct Air offers a range of reliable and premium quality products that will bring years of comfort and peace of mind to your family. Once the water tank is completely drained and no more water flows out, reinstall the cap. Shinco Air Conditioner Error Codes: Inverter Split System Air Conditioner R410ACheck Point: Check If The Indoor Unit Match Outdoor UintFault: Communication Fault Between Indoor Unit And Outdoor UnitCheck Point: Check If Wirings Between Power Board And Driver Board Are Connected WellCount Measure: Fix The Wiring Between Power Board And Driver BoardFault: Communication Fault Between Indoor Unit And Outdoor UnitCheck Point: Check If The Indoor Unit Match Outdoor UintPress the ON/OFF button 6 times within 7 seconds, there will be three DU sound on indoor unit, and the indoor unit will display the fault code.KFR-25GWZ/BM, KFR-35GWZ/BM, KFR-50GWZ/BM, KFR-70GWZ/BMBefore calling a repair man, please check the followings:Possible reason: Moisture will occur in the air outlet due to the temperature differenceHave same problem , Do your know of a source for parts (out door discharge pipe sensor)where is the driver board located and whatis ACI,PCB board,CAN,PFCI have 2.2 message with all the other symbols lights up and the system just stop working.
I have also opened the cover to ensure a working float switch. This is a normal operation. Facebook Share
There is an overload protector sensor located on the top of the compressor that sends the signal it is overheating.Several things can cause this error with the steps below for what to check.The owner of this website, www.hvachowto.com, is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking www.hvachowto.com to Amazon properties including, but not limited to, Amazon.com, Amazon.ca, Amazon.co.uk, Amazon EU Associates Programme, Amazon.it, Amazon.es, Amazon.fr, endless.com, myhabit.com, smallparts.com, or amazonwireless.com Instead of shutting the air conditioner completely off when away from the home, raise the temperature to a higher setting. toggle menu Twitter Share
Under normal operating conditions, the drain pan will not need to be emptied.
The unit is designed with a slinger fan that is mounted above the drain pan.
Below are the steps to troubleshoot and fix an P2 error code.This means the main board is reading the compressor is overheating and sending out the P2 error.